This article will provide a complete guide on Factory resetting the UniFi switch, including essential steps to back up your existing configuration. Go through each step, from connecting to the button to reconfiguring it after the reset. Following the steps in this guide, you can Factory reset UniFi switch to its default settings and troubleshoot any issues you may be experiencing.
First, connect the UniFi switch to a computer using a serial cable for a factory reset. For 10 seconds, you need to press the reset button. After you release the controller, the switch will return to its factory preset settings. Doing this will restore the switch’s factory settings.
By reading the entire article, you will understand how Factory reset their UniFi switch, including essential steps to back up their existing configuration and reconfigure the button afterward. It will allow you to troubleshoot any issues they may be experiencing with their control and restore it to its default settings as a last resort. Following the detailed steps in the article, you can confidently and successfully Factory reset the UniFi switch.
Table of Contents
How to Factory Reset UniFi Switch?
A factory reset UniFi switch is a common troubleshooting step that can help resolve various issues with the device. Restoring the factory default settings will erase all the current configurations and locations on the switch, allowing you to start fresh with a clean slate.
After all other switch troubleshooting methods have failed, a factory reset should only be used as a last resort. It is crucial to understand that performing a factory reset won’t resolve any hardware problems with the switch and shouldn’t be done as part of regular maintenance.
Before we get started, it’s important to note that Factory resetting your UniFi switch will remove all configuration settings, including VLANs, port configurations, and any custom settings you have made. It’s, therefore, crucial to back up your current design before proceeding with the reset.
Here are the ways you can Factory Reset the UniFi Switch:
Connect to the Switch Using a Web Browser
Try to use a web browser on a computer connected to the same network as your Factory reset unifi switch to connect to it. Filling your web browser’s address bar with its IP address would be best.
It is located in the DHCP server client table or at the bottom of the switch. Press Enter to open the switch’s web interface after entering the IP address.
Log in to the Switch
When you first access the switch’s web interface, you will be prompted to log in. “ubnt” is the password and username by default.
If you have previously changed your UniFi login credentials, you must use the updated username and password to log in.
Back up Your Existing Configuration
It’s crucial to back up your current setup before the factory reset. It will allow you to transfer the same configuration to another UniFi switch quickly or, if necessary, restore your settings. In the top menu, click the “Settings” tab, then select the “Setup” sub-menu to back up your configuration.
Click the “Export” button on the Configuration page. Your computer will subsequently download a duplicate of your current setup UniFi. This file will be necessary to restore your settings after the Factory reset the unifi switch, so keep it in a secure area.
Factory Reset UniFi Switch
To factory reset the UniFi switch, click on the “Devices” tab in the top menu, then click on the name of your UniFi switch in the list of devices. Click the “Configuration” tab on the switch’s page, then scroll down to the “Manage Device” section.
Click the “Factory Reset” button in this section. It will start the factory reset procedure, which could take a while to finish. If you want to learn how to reset your account name and password for Ooredoo Router, click here.
Reconfigure the Switch
After the Factory reset, the UniFi switch process is reset to default settings. It indicates that for the switch to function with your network, it needs to be reconfigured. Open the top menu, then choose “Settings” from the list. Select the “Network” sub-menu after reset.
Throughout the entire network, the following choices will be the same: on the Network page; you can learn how to configure the switch’s IP address, subnet mask, and default gateway. You can modify the switch’s VLAN settings on this page if necessary.
Restore your Previous Configuration
By selecting the “Settings” tab on the top menu, then selecting the “Setup” sub-menu, you can restore your initial configuration if you have a backup. Click the “Import” button on the configuration screen.
It will enable you to choose and apply to your UniFi switch the configuration file you previously downloaded. It will restore all of your old settings, including port configurations, VLANs, and custom settings, which might save you time and effort when reconfiguring your settings.
See Also: TP-Link Router not working after reset
Save your Chances and Reboot the Switch
Once you’ve adjusted the settings on your UniFi switch for factory reset unifi switch, click the “Apply Changes” button in the top right corner to save your changes.
After reset, select “Devices” from the top menu to effect the modifications, then click on the name of the UniFi switch. UniFi is on the list of available devices. Click the “Configuration” tab on the switch’s page, then scroll down to the “Manage Device” section. To restart the switch, use the “Reboot” button in this area.
See Also: Vodafone router login.
FAQs
How do I set up the UniFi Switch 8 60W?
UniFi Switch 8 60W/60W setup is easy; I need to connect it to your network and then configure it through the UniFi Controller software. First, connect the switch to your network by plugging an Ethernet cable into one of the switch's LAN ports and the other end into a router or network switch. Next, power the switch and download the UniFi Controller software onto a computer on the same network. After installing the software, follow the on-screen instructions for adding and switching configures.
What is the UniFi switch default password?
The UniFi switch default password is 'ubnt.' The default password for most UniFi devices, so it is recommended to change the password after the initial setup to improve the security of your network. To change the password, log in to the device's web interface using the default password and navigate to the Settings tab. You can change the password in the 'System' section.
How to force an UniFi switch
To adopt an UniFi switch, connect to the switch using SSH and issue the 'set-inform' command. It tells the switch to connect to the UniFi controller and start the adoption process. In the controller, click on the pending device to complete the adoption. If it has, you will need to reset it to factory defaults first, and then Factory reset the UniFi switch.
How can I restart my 8-port UniFi switch?
Button to Reset For the UniFi Switch, this button has two uses: Restart Quickly press and release the reset button. The Reset button should be pressed and held for more than five seconds. Reset all settings to factory defaults.
Conclusion
A factory reset UniFi switch can be a helpful troubleshooting step, as it resets all configuration settings back to their default values. However, it’s essential to back up your existing configuration before proceeding with the reset, as this will allow you to restore your settings if needed. Following the steps, you will learn how to reset your UniFi switch and reconfigure it to work with your network.
Originally hailing from Troy, Ohio, Ry Crist is a text-based adventure connoisseur, a lover of terrible movies and an enthusiastic yet mediocre cook. He has a strong appreciation for nifty, well-designed tech that saves time, looks stylish, and/or helps him avoid burning his dinner quite so often. Ry lives in Louisville, Kentucky.
