Every modern device that a user uses to access the network comes along with a Default IP address such as 10.0.0.1. It is developed in such a way that only the devices that are connected to this network can access this default IP address. That’s why they are said to be a private network. No device can access this IP address outside this network.
NOTE: – Always type correct IP address in your browser i.e. “10.0.0.1” Most of the times we end up typing wrong IP such as 10.0.0.0.1, 10-0-0-1, https //10.0.0.1 login, http //10.0.0.1, http //10.0.0.0.1, 10.0.0.1., www.10.0.0.1.
About the IP address 10.0.0.1
Specially routers, the default IP addresses play a very crucial role in this. Routers are created in such a way that the configuration can only be done by accessing the IP address 10.0.0.1 admin login. One can assign any IP address to the router such as 192.168.0.1 or say 192.168.1.1 other than 10.0.0.1.
By the default IP address like 10.0.0.1, you can access the router admin page to configure the settings. You can use default credentials, i.e., default password and username to login into the Admin panel of the router. The Admin panel can configure various aspects of the router such as blocking particular devices to access the network, network name, network security type, network password, wireless setup, etc.
Secondly, also the default IP address assigned to any system helps in communication with the other systems.
As 10.0.0.1 is a type of default IP address, it doesn’t mean that it can be accessed only via particular computer or router. Any device can access this type of IP addresses inside the private network.
How to login 10.0.0.1
Though logging into the Admin panel via the IP address, 10.0.0.1 is not a huge task. But it can be a mess when difficulty in finding the default password and username for the default gateway comes into play. You can see it behind the router printed near the IP address 10.0.0.1 if it is not invisible yet due to wear and tear.
Well, for xfinity router login, follow the steps below and see how simple it is
- Open the web browser of your system and make sure it updated with the latest version available.
- Now type 10.0.0.1 in the address bar and hit enter.
- Now a page will appear and ask you to enter the default password and username for the IP address 10.0.0.1.
- The page will load after a moment showing the configurations of the router in the Admin panel.
So, if you want to login the IP address 10.0.0.1 from the router. You have to get the default password and username before even setting the new credentials.
These password and username are set of default credentials. Therefore one can use these only when the router is in the reset state or when one does not change the password.
What if you Forget the Username and Password?
Forgetting passwords isn’t a big deal, of course, we are humans. So what after this when you forget a password for router access where you can’t send a request to reset the password via OTP? In the case when you forget the default password and username isn’t a big issue.
But after setting a password of your choice and forgetting it, can cost you the configurations of router. It is so because to gain the access to the router Admin page you will have to reset the router. After doing this, all the earlier settings will not be applicable anymore.
But you have no option other than resetting the router and bring back to it’s default state. So follow the steps below for that
- Grab a pointed end tool such as a needle or compass so that it will pass through the narrow opening.
- Now you have to press the button on the back side of the router. And also keep holding it for like 5-10 seconds.
- Do it, until all the lights on the router glow at once and turn off again.
- This indicates that the process is complete and the router is ready to login
- Now, you will be able to login with the default password and username.
Note that one can use the method above, only in cases where password and username set other than the default credentials is unknown. It is because it will force the network to reset all the configurations made by the users earlier.
We can conclude that one can use IP addresses such as 10.0.0.1 to assign the router as default gateway. This means, they provide a way to access the configuration admin panel. Also, they help a system to communicate among the different systems.
Some of Devices that uses 10.0.0.1 as the default gateway are Alfa, airlink101, Alfa network, apple, Arris, aztech, Belkin , Cisco, etc. They are used as wireless router, access point, etc.
To maintain the network one should be familiar with the different aspects of the admin panel to make the settings when needed. And also people knowing admin panel better can make the internet more secure and faster.